ACI Middle East Page · Sign In Acceptance Criteria for Qualification of Post-Installed Adhesive Anchors in Concrete & Com:Provisional Standard. Find the most up-to-date version of ACI at Engineering 1 Aug ACI Qualification of Post-Installed Adhesive Anchors in Concrete and Commentary. standard by American Concrete Institute, 08/01/.
|Published (Last):||4 November 2009|
|PDF File Size:||13.79 Mb|
|ePub File Size:||9.74 Mb|
|Price:||Free* [*Free Regsitration Required]|
The design aci 355.4 deemed to satisfy the anchor design requirements of ACIAppendixD, is based on an analysis of an anchor database with a maximum diameter of 2 in. Not Cai In Member?: Identify unmet needs and discover next-generation technologies Improve quality by leveraging consistent standards to meet customer and market requirements Minimize risk: Refer to Aci 355.4 for a review of factors that influence adhesive anchor behavior.
Standard: ACI 355.4
DRM is included at the request of the publisher, as it helps them protect aci 355.4 copyright by restricting file sharing. The minimum member thickness shall not be less than the value given by Eq.
ACI addresses aci 355.4 situation by matching capacity reduction factors to anchor performance categories that are, in turn, established through a series of reliability tests. This standard applies only to post-installed adhesive anchors as defined herein.
IHS Standards Expert subscription, simplifies and aci 355.4 the process for finding and managing standards by giving you access to standards from over standards developing organizations SDOs. Visit FileOpen to see the full list. Criteria are prescribed to determine the design parameters zci performance category for adhesive anchors.
This standard aci 355.4 available for individual purchase. Full Description This standard prescribes testing and evaluation requirements for post-installed adhesive anchor systems intended for aci 355.4 in concrete under the provisions of ACI Criteria are separately prescribed to determine the suitability of adhesive anchors used in uncracked concrete only, or in both cracked and uncracked concrete.
Speed up research, aci 355.4 aco reuse expertise For additional product information, visit the IHS Standards Expert page. Included are assessments of the adhesive anchor system for bond aci 355.4, reliability, service conditions, and quality control.
Introduction and scope Aci 355.4 standard prescribes testing and evaluation requirements for post-installed adhesive anchor systems intended for use in concrete under the provisions of ACI Appendix D requires that anchors be tested either for use exclusively in uncracked concrete or for use in cracked and uncracked xci conditions, whereby it is understood that the presence of cracking may occur at any time over the service life of the anchors.
The upper limit on the ratio of hole diameter to anchor element diameter provides a demarcation between conditions where a sci bond strength can be used to evaluate anchor strength and aic where bond strengths at both the anchor interface and aci 355.4 interface must be determined to evaluate anchor strength.
Click here to skip or ad will close in 15 seconds. Included are assessments aci 355.4 the adhesive anchor system for bond strength, reliability, service-conditions, and quality control. Adhesive anchors resist tension loads with a combination of adhesion and mechanical bond micro-interlock.
finally meeting the requirement of ACI is mandatory or not? – Ask Hilti
A limitation on the minimum embedment length of adhesive anchors is necessary to ensure conformance with the design method aci 355.4 to satisfy the anchor design requirements of ACI aci 355.4, Appendix D. In addition, the value of 1.
They were placed aci 355.4 your computer when you launched this website. Speed up research, capture and reuse expertise For additional product information, visit the IHS Standards Expert page. This Standard References Showing 10 of Click here to skip or ad will close in 15 seconds. This standard prescribes the testing programs required to qualify post-installed adhesive anchor systems for design in accordance with ACI Appendix D.
In particular, the sensitivity of adhesive anchors to variations in installation and service-condition parameters such as hole cleaning, installation orientation, and cracked concrete characteristics may vary widely from each system.
This Standard References Showing acu of Criteria are prescribed to determine the design parameters and performance category for adhesive anchors. Mitigate liability and better understand compliance regulations Boost efficiency: What aci 355.4 can do aci 355.4 a Secure PDF: